Windows 7 startup repair cmd

Wait for Windows 7 installation files to load. Then Startup Repair will repair startup problems automatically for Windows 7. And the whole process might take a few minutes, please wait patiently.

But sometimes it does not work as expected, just as the user case above. Then, how to fix Startup Repair cannot repair this computer automatically in windows 7? After you have realized possible reasons for Windows 7 not booting and error message that you can receive, it is time to get to know how to solve this problem without reinstalling.

Restart your computer. Then, when you see the Windows log, press F8 repeatedly until you see the Advanced boot options window. It will scan the integrity of the file system errors or bad sectors and fix it finds. Select Repair your computer in the Advanced boot options window and hit Enter.

After the process finishes, you can exit from Command Prompt and check whether you can boot Windows 7 computer normally. Microsoft Windows operating system occupies most of the market land.

The most common Windows operating system includes Windows 7, Windows 8, Windows 8. However, we are going to talk about Windows 7 today. Incorrect boot order sequence in BIOS. Thus, check your BIOS boot order to make sure the system hard drive is the first boot device. Damaged system hard drive. Run anti-virus software to see if there is malware, or you might have to replace the system hard drive with a new one.

The first two factors are easy to resolve. If you upgrade Standard to Professional edition , you can enjoy more amazing functions like recovering deleted boot partition , extending system drive, quickly partitioning hard disk without formatting, and more.

Damaged BCD settings If the boot sector is infected by viruses and other malware, the bootloader and booting chain will get damaged. Method 1. Rollback to the recent Windows 7 update If your Windows 7 is stuck into an infinite Startup Repair loop after an update, you can try to roll back the Windows 7 update in the Safe Mode since the Windows cannot boot as normal. Find out the most recently installed updates, which most likely has caused the Startup Repair loop, 4. Method 2. Disable Automatic Restart you can try to disable or cancel automatic restart, although it could not solve the boot error, it can provide more information to help you find out the real culprit.

Method 3. Run chkdsk on the boot volume The command line chkdsk tool can be used to check, or even repair the drives to tackle file system corruption. To run chkdsk, please do as follow: 1. Method 4. Run bootrec to fix damaged or corrupted BCD settings If the bootloader installation or configuration comes with some errors, the Startup Repair loop could happen as well. Method 5. Perform a System Restore Since System Protection is enabled by default, you can use it to restore your computer to an earlier state.

Method 6. After that, you will go to the Install Windows screen, click Repair your computer. Step 7. Sometimes, you will not see any operating system in this window, please click Load Drivers to install drivers for your disks. Step 8. Just wait patiently until the process is completed and click Finish.

When you try to manually run Startup Repair using installation disc, you may find startup repair not working sometimes and ask you to restore your computer with System Restore. Click Restore if you have a working restore point. If not, click Cancel. Then, you will see the Windows cannot repair your computer automatically screen with 2 options at the lower location, select " View advanced options for system recovery and support ".

After that, you will go back to the System Recovery Options window and select Command Prompt to boot repair Windows 7. Then, it will automatically pop up. Wait a minute, please try Windows 7 startup repair command prompt chkdsk to scan the integrity of your file system and hard drive so as to rule out the physical problem of hard drive.

Because it can also damage the boot sector and MBR. Then, try other command lines below. In the command prompt window, type the following command line and hit Enter after each one.

In the command prompt window, type the following command line in order and then hit Enter. If the above command prompt does not work for you, you still can try to backup and rename BCD first and then rebuild it via CMD. Step 2. Then, type notepad in the command prompt window. After that, save the change and exit this window. Now, you will go back to the command prompt window.